IC rated, low voltage, energy efficient, Air-Loc sealed
double wall construction housing does not require
separate Air-Loc gasket • Can be completely covered
with insulation • Air-Loc housing with all trims stops
infiltration and exfiltration of air, reducing heating
and cooling costs
Listings
UL Listed, C-UL/CSA certified for through-branch
wiring, damp and wet locations • Washington State,
IECC and MEC energy codes as tested per
ASTM-E283 • Wet location listed with trims 441, 4401,
4402 and 4481 • Conforms with City of Chicago IP
requirements
Lighting Housing Features
- 4 inch Housing
- Ceramic bi-pin socket with aluminum heat shield
- Housing is vertically adjustable to accommodate
up to a 1 inch ceiling thickness
- Aluminum housing is fully assembled for ease of
installation
- 120V to 12V 50VA thermally protected magnetic
transformer
- May be dimmed using dimmers specifically
designed for magnetic transformers
- Real Nail™ 3 bar hangers: telescoping system with
pre-installed removable nail for easy repositioning
of housing in joist construction
- Integral T-bar
clip for secure installation in suspended ceilings
- Patented break-away bars for tight joist spacing
- Bar hangers may be re-positioned 90º
- Curved
foot facilitates alignment with joist bottom
- Quick-Loc slot and oversized set screw lock
fixture in position
- Pre-wired junction box with (6) 1/2 inch and (1) 3/4 inch
knockouts with pryout slots, (4) Romex™
connectors, and ground wire
- Shadow-free, knife-edge trim design blends
smoothly into the ceiling and allows architectural
continuity with Aculux™ trims
- UL Listed, C-UL/CSA certified for through-branch
wiring, maximum (6) #12 AWG minimum 90 Degree C
branch circuit conductors (3 in, 3 out)
- Thermally protected against improper use of
lamps
Lighting Housing Specifications
Lamp One 12V, 50W MR16 lamp.
Socket Ceramic bi-pin socket with aluminum heat shield.
Trims Trim selection shown on reverse.
Transformer 120V to 12V 50VA thermally protected magnetic
transformer mounted inside outer housing.
Dimming May be dimmed using dimmers specifically designed
for low voltage magnetic transformers; consult factory or dimmer
manufacturer for additional information.
Labels U.L. listed for through-branch wiring, damp locations and
IP • Product thermally protected against improper use of lamps
• Union made AFL-CIO • UL Listed/CSA certified • Trim No. 441,
4401, 4402 and 4481 are wet location approved for covered
ceiling applications.
Testing All reports are based on published industry procedures;
field performance may differ from laboratory performance.
Product specifications subject to change without notice.
Lighting Housing Installation
Real Nail 3 Bar Hangers Telescoping, patent-pending Real Nail 3
system permits quick placement of housing anywhere within 24 inch
O.C. joists or suspended ceilings • Integral T-bar notch and clip
secures housing in suspended ceiling grid – no accessory clips
required • 24 inch expansion stop allows quick placement of fixture
in standard grid spacing • Bars scored in two locations for fast,
clean breaking, allowing housing installation in tight applications
• Bars captive to mounting frame • Edge-mounted for extra
strength • Captive bugle-headed ring shank nail for quick one-step
installation and easy removal with claw hammer for fixture
relocation • Quick-Loc slot and oversized locking set screw lock
fixture in position • Bar hanger foot contoured to align to bottom
of construction joist • Alternate mounting holes included.
Junction Box Pre-wired junction box provided with (5) 1/2 inch and
(1) 3/4 inch knockouts, (4) Non-metallic sheathed cable connectors and
ground wire, U.L. listed/CSA certified for through-branch wiring,
maximum 6 No. 12 AWG 90 Degree C branch circuit conductors (3 in,
3 out) • Junction box provided with removable access plates
• Knockouts equipped with pryout slots.
Mounting Frame 22-gauge die-formed galvanized steel
mounting frame • Rough-in section (junction box, mounting frame,
housing and bar hangers) fully assembled for ease of installation.
Housing Air-Loc IC housing, .032 inch aluminum • Access door for
junction box accessibility • Housing is vertically adjustable to
accommodate up to a 1 inch ceiling thickness.
